It sounds like you have a Create-A-Breeze 8000 Series Roof Vent and in which case you'll need to replace the fan and motor as one using the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans part # FVK8017-00. view full answer...
I would need to know the brand and model of your AC unit in order to find the correct replacement, but I've gone ahead and listed some common units below:
Penguin and Dometic Air Conditioners # AT3308046006
Dometic Brisk Air II # DMC46FR
Dometic Duo-Therm # DMC69FR
Coleman-Mach / RVP Brand # MA8335A5261
Advent Air Units # PXXMCOVER
Atwood Air Command # AT15050 view full answer...
Yes, you can manually adjust self-adjusting brakes with a spoon like the drum brake spoon # W80630. We've done it here in the office years ago because we weren't sure if it was possible but it is. It is harder to get to the star wheel that adjusts the brake on self adjusting assemblies but it is possible. You'll need to remove the plugs on the back of the assemblies.
For replacement assemblies we do have the set you mentioned of # K23-478-479. view full answer...
It is possible you will have to remove your screen door in order to use the MORryde StepAbove Fold-Down Steps for 21-3/4" to 22-1/4" RV Door Frames # MR58RR.
The answer just depends on the gap you have between the bottom of your screen door and your threshold. As you can see by the cut out I added from MORryde, you will need a gap of at least 3/8" between the bottom of your door and threshold in order for the steps to work for you.
I have added a link below to the installation instructions... view full answer...
That is correct.
You will need to use the Replacement Control Key for Yakima Same Key System # Y8007835 to remove your current lock core, but the lock core will need to be unlocked for the control to be able to remove the core. If the lock core is locked you will need to have a locksmith unlock it for you first.
Once the core is removed you will see the key code stamped in the side of the lock core as shown in the included picture of the # Y8771-A137. For example if your lock core was... view full answer...
I have an option that may work for you, but the largest lift kit for a torsion axle is 3-1/2".
We offer a few different torsion axle lift kits including the Axle Riser Kit - Single Diamond Torsion Axle - 3-1/2" Lift # LC270682 and the Axle Riser Kit - Single Square Torsion Axle - 3-1/2" Lift # LC382741.
Both of these options offer 3-1/2" lift which is the highest offered, but will only work if the axles on your 2012 Forest River Rockwood Signature Ultra Lite 5th Wheel trailer uses Lippert... view full answer...
We know that your Rockwood Signature Ultra Lite uses a Lippert 1621 pin box so the correct MORryde pin box would be the # MR84VR that you referenced. view full answer...
The Replacement Slide # A77014 measures 10-3/4" Wide x 12-1/8" Tall and is designed for Elixir RV Screen Doors. I'm not sure what exactly you have on your 2014 Rockwood Signature Ultra Light but if this doesn't match up you can measure your slide and either filter through the linked selection or let me know what you have and I can see if we have something that is compatible. view full answer...
The correct replacement antenna for the FRC12TA-BL Furrion observation system is the Replacement Antenna for Furrion Vision 1, 2, and S Wireless RV Camera Systems # 772577.
I was unable to find any information specifically on the "BLC" but I believe that may just be a combination of part numbers and so long as you have the FRC12TA designation this antenna will work.
I have added links to a couple video reviews for you to check out as well of the Replacement Antenna # 772577. view full answer...
The correct Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter for your 2011 Forest River Rockwood Signature Ultra Lite 8286WS is part # RP85FR. This pin box measures 12" wide which is the same for all pin boxes that fit a Lippert 1621 wing set.
If you have a Lippert 1621 wing set then the distance between your wings will be 12" (inside to inside). I would verify your measurements but there is not any sort of adapter for this because the 12" width is an industry standard... view full answer...
You may be able to combine a torsion lift kit and larger tires and wheels to get you close to the 4" lift that you are looking for. Currently there is not a torsion lift kit that will raise your 2011 Forest River Rockwood 8244S that much.
I've had a bit of a hard time figuring out exactly what axles are under your Rockwood. I do know that they are 3,500lb axles which narrows down the possibilities. You may have a Dexter #10 Torflex. You can determine if you have this by measuring the... view full answer...
I would be happy to help you. I don't have any way of knowing what type of landing gear you have on your 2010 Forrest River 5th Wheel to possibly find a matching replacement leg. Since you are ok replacing both front legs and have weld stops at 17-1/2" and 15-1/2" the Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs item # RVLG-8HDL you were looking at would work.
If you current motor does not fit the new gear set you will want to use the Lippert Venture 5th Wheel RV Landing Gear... view full answer...
You are going to need a new camera system like the Furrion Vision S with a 4.3" Monitor # FOS43TASF or 5" Monitor # FOS05TASF. Furrion discontinued your FRC12TA-BL when they changed the way their cameras and monitors communicate. Because of this you have to upgrade both the monitor and camera.
The 4.3" version will work with the single monitor while the 5" kit will also allow you to add and connect Side Cameras # FCE48TASL.
Do note if you are using a newer truck you may need the Furrion... view full answer...
The Reese 10k Revolution was a uniquely designed pin box that can only be replaced with another 10k Revolution. Your 10k Revolution is a sidewinder so if you're using a slider it must be locked out. You can unlock it by removing the lock out bolts like you can see in the attached picture and adding on a Sidewinder Wedge Kit for Curt A-Series and E-Series Fifth Wheel Trailer Hitches Item # RP64FR and locking out your sliding hitch. Doing this will move the pivot point further back than the... view full answer...
The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set # LC358590 will work fine with your 2014 Forest River Rockwood Signature Ultra Lite Fifth Wheel trailer. The weight of your trailer and the mounting brackets will work just fine to give you the automatic leveling you desire. I've attached a photo of the rear mounting bracket and jack to help you see how it installs. view full answer...
From my research and experience installing steps on fifth wheel campers your 2013 Forest River Rockwood Signature Ultra Lite Fifth Wheel the door opening should be 30" to 36". If I am correct I recommend SolidStep Manual Fold-Down Steps for 30" to 36" Wide RV Door Frames - Quad - Aluminum Item # LC791575. Most fifth wheel campers sit a little higher. Having the fourth step ensures the bottom step is not too far from the ground. The steps have adjustable legs for un-level terrain so you... view full answer...
Yes the Furrion Vision S Observation system part # FR98NR would work great on your 2015 Forest River Signature Ultra Light fifth wheel camper. This kit can basically install on any camper and would do so very easily due to it's universal design.
For more info on this kit check out the review video I attached. view full answer...
The Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs # AKEBRK-35-SA are not Husky brakes, they are from AxleTek. While we don't offer Husky brakes so I'm not familiar with them, all electric brakes, including our AxleTek, have two wires, and either wire can be used for power or ground, it doesn't matter which.
With the # AKEBRK-35-SA, the only thing you will need for the install is the Mounting Hardware # BRKH10B.
I have added a link below... view full answer...
With you having 4,000 pound torsion axles, you will need to double check something before moving forward. Though both of these options will measure 10 x 2 1/4 inches, there is a big difference between them.
The etrailer.com Self-Adjusting # AKEBRK-35-SA will have a bolt pattern of 2 7/8 inches from center to center of all 4 bolt when moving around them in a clockwise manner. You can also go center to center of 2 bolts diagonally to get 4 inches. These are rated to 3,500 pounds per axle... view full answer...
Go To Results